Using a Double line winch pull method with a snatch block can when properly accomplished give you 2x the pulling power of your winch.
***Basic Tool Box:*** Can be as extensive or as minimal as you wish. Here is an example of jobs, and tools needed, you may need to perform on the trail – (Sizes vary – make sure you have the tools for *Your* specific vehicle) 1.Remove Brakes 15mm 21mm 2.U-joint replacement 15mm socket / hammer / […]
Explanation of what you need to do to actually be able to remove your freedom top panels and hardtop. Bolts to remove, levers to move, latches to unlatch, connectors to disconnect, etc.. This video has a hoist system which is used. Manual removal is explained as well.Shout outs to https://www.facebook.com/IG4wlusa/, https://www.sevenslotsociety.com/, http://onthetrailpodcast.com/ w/Kevin and Scott. […]
So easy a Jeeper Figured it out. What is Wheel Offset and Backspace? Wheel offset and backspacing two different ways of looking at same thing. Determines the location of the wheel and tire assembly when bolted onto the wheel hub. They determine how far in or out the wheel and tire sit. Why is it […]
Front ends shakes, wobbles, shimmies and the dreaded Death Wobble. These have been going on since steering was invented and has worsened with the incorporation of coil spring suspensions. Prevention is the key to any well maintained Jeep. Preventive Maintenance and Routine Inspections and not of just the Stereo Equipment. We used a Floor Jack, […]
Parts Recommended:Upper and Lower Intake Gaskets – MS97204Oil Filter/Cooler Housing – 68105583AE Tools Required: 8mm Socket 10mm Socket Ratchet 3” and 6” extensions Body Clip Tool T20 Torx T30 Torx E8 (External) Torx Small flat tip screwdriver Standard Pliers Wide Tape to cover intake ports Brake Cleaner or similar, to clean intake and oil filter/cooler […]
Tools Needed: 10mm Wrench, 14 mm Wrench, 16mm Wrench, 18mm Wrench, 18mm Socket, 19mm Wrench, 19mm Deep Well Socket, 7/8″ Wrench, 13/16″ Socket, 21mm Wrench, 21mm Socket, 7/16″ Wrench, 9/16″ Wrench, 9/16″ Socket, 33mm Socket, Jack, (4) 6 ton Jack Stands, (2) 3 ton Jack stands, 13/32″ Drill bit, Drill, Pitman Arm Puller, PB Blaster, […]
Jeep Wrangler JK JKU Pinion Bearing Removal and Replacement Refer to JK_JKU Hub Bearing Replacement video for more detailed instructions on removal and Installation of the Hub Bearing and Axle Shaft. https://youtu.be/9uOOXPxBr8M Tool Suggested: 1/2″ Drive Ratchet 1/2″ Drive Breaker Bar 1/2″ Drive Torque Wrench capable of 120 ft lbs 3/8″ Drive Ratchet 1/4″ Drive […]
This is specifically for Iron Rock Offroad Adjustable Control Arms – After installation and testing has occured, it is time to adjust for better performance. This process is similar for most adjustable control arms, clamping nuts and bolts may differ but the procedure is the same.
Left Side (Driver Side) Exhaust Manifold Replacement on a Jeep Wrangler JK or JKU (3.8L Motor) Applies to 2007-2011 Jeep Wrangler (JK/JKU) Exhaust Manifold Replacement Mopar PN: 4666024AD Exhaust Manifold Gasket Replacement FelPro PN: MS 96908 Tools Recommended: 10″ Vise Grips 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive 14″ extension […]