Do It Yourself – Simple Step by Step Instructions on How to Remove and Replace The Oil Filter / Cooler Assembly on your 2012 and Newer Jeep Wrangler using common tools

by Kurt EadesLearn, VideoPosted on No Comments

Parts Recommended:Upper and Lower Intake Gaskets – MS97204Oil Filter/Cooler Housing – 68105583AE Tools Required: 8mm Socket 10mm Socket Ratchet 3” and 6” extensions Body Clip Tool T20 Torx T30 Torx E8 (External) Torx Small flat tip screwdriver Standard Pliers Wide Tape to cover intake ports Brake Cleaner or similar, to clean intake and oil filter/cooler …

Read more “Do It Yourself – Simple Step by Step Instructions on How to Remove and Replace The Oil Filter / Cooler Assembly on your 2012 and Newer Jeep Wrangler using common tools”

Do It Yourself how to Install a 3.5 inch Suspension Lift Kit on a 2007 – 2018 Jeep Wrangler

by Kurt EadesLearn, VideoPosted on No Comments

Tools Needed: 10mm Wrench, 14 mm Wrench, 16mm Wrench, 18mm Wrench, 18mm Socket, 19mm Wrench, 19mm Deep Well Socket, 7/8″ Wrench, 13/16″ Socket, 21mm Wrench, 21mm Socket, 7/16″ Wrench, 9/16″ Wrench, 9/16″ Socket, 33mm Socket, Jack, (4) 6 ton Jack Stands, (2) 3 ton Jack stands, 13/32″ Drill bit, Drill, Pitman Arm Puller, PB Blaster, …

Read more “Do It Yourself how to Install a 3.5 inch Suspension Lift Kit on a 2007 – 2018 Jeep Wrangler”

How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others

by Kurt EadesLearn, VideoPosted on No Comments

Jeep Wrangler JK JKU Pinion Bearing Removal and Replacement Refer to JK_JKU Hub Bearing Replacement video for more detailed instructions on removal and Installation of the Hub Bearing and Axle Shaft. https://youtu.be/9uOOXPxBr8M Tool Suggested: 1/2″ Drive Ratchet 1/2″ Drive Breaker Bar 1/2″ Drive Torque Wrench capable of 120 ft lbs 3/8″ Drive Ratchet 1/4″ Drive …

Read more “How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others”

exhaust manifold

How to Remove and Replace on a Driver Side Exhaust Manifold on a Jeep Wrangler JK/JKU (3.8L Motor)

by Kurt EadesLearn, VideoPosted on No Comments

Left Side (Driver Side) Exhaust Manifold Replacement on a Jeep Wrangler JK or JKU (3.8L Motor) Applies to 2007-2011 Jeep Wrangler (JK/JKU) Exhaust Manifold Replacement Mopar PN: 4666024AD Exhaust Manifold Gasket Replacement FelPro PN: MS 96908 Tools Recommended: 10″ Vise Grips 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive 14″ extension …

Read more “How to Remove and Replace on a Driver Side Exhaust Manifold on a Jeep Wrangler JK/JKU (3.8L Motor)”

Water Pump

Do It Yourself – How to Remove and Replace the Water Pump on a Jeep Wrangler JK / JKU 3.8L Motor

by Kurt EadesLearn, VideoPosted on No Comments

This procedure applies to 2007-2011 Jeep Wrangler (JK/JKU) with a 3.8l V-6 Motor Parts Used:Water Pump Replacement Mopar PN: 4666044BB.0Water Pump Gasket Replacement Mopar PN: 4666068AA Tools Recommended: Wire Brush Gasket Scraper Small Pry Bar 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive Breaker Bar 3/8″ Drive 10mm Socket 3/8″ Drive …

Read more “Do It Yourself – How to Remove and Replace the Water Pump on a Jeep Wrangler JK / JKU 3.8L Motor”

Hub Bearing

Do It Yourself – How to Remove and Replace a Hub Bearing on a 2007 – 2020 Jeep Wrangler Unlimited

by Kurt EadesLearn, VideoPosted on No Comments

This is the removal and replacement of a 2009 JKU Passenger side Hub Bearing. This video starts after you have already raised the Jeep and supported it properly with jack stands and removed the tire. This procedure should work for many other years and models of Jeep. 1987-2018. There will be slight variations in the …

Read more “Do It Yourself – How to Remove and Replace a Hub Bearing on a 2007 – 2020 Jeep Wrangler Unlimited”

Evap Relocation

Do It Yourself Video – Simple How to on Relocation of your Fuel Evaporator Canister on a 2007 – 2018 Jeep Wrangler JK or Unlimited

by Kurt EadesLearn, VideoPosted on No Comments

This is a How To video on “one” procedure for relocating your evap canister on a 2007-2011 Jeep Wrangler JKU. This solves the issue of bolts sticking thru the bottom of the back trunk area of the Jeep. I used flat headed beveled shoulder bolts with hex head with a lock nut and a flat …

Read more “Do It Yourself Video – Simple How to on Relocation of your Fuel Evaporator Canister on a 2007 – 2018 Jeep Wrangler JK or Unlimited”

Starter

Do It Yourself – How to Replace a Starter on your Jeep Wrangler JK or Unlimited

by Kurt EadesLearn, VideoPosted on No Comments

Procedures on how to remove and replace your starter on a 2007-2011 Jeep Wrangler JK / JKU, This procedure is very similar on all Jeep Wrangler Models and early Model Jeeps Tools 3/8″ Ratchet 3/8″ 13mm socket 3/8″ 15mm socket 3/8″ 16mm socket 3/8″ 6″ Long extension 3/8″ Universal Swivel adapter Parts Used: CarQuest Starter …

Read more “Do It Yourself – How to Replace a Starter on your Jeep Wrangler JK or Unlimited”

Pulley and Belt

Do It Yourself – How to Replace the Idler Pulley and Belt on your 2007 – 2011 Jeep Wrangler

by Kurt EadesLearn, VideoPosted on No Comments

Removal and Replacement of the Idler Pulleys and Serpentine Belt in a Jeep Wrangler (2007-2011) Replacing the Idler Pulley, Tensioner Pulley and Serpentine Belt on a 2007-2011 Jeep JK or JKU Tools 3/8″ Ratchet or breaker bar 13mm socket 16mm socket Parts: With A/C Serpentine Belt – PN: K060900 Tensioner w/Pulley – PN: 39269 Idler …

Read more “Do It Yourself – How to Replace the Idler Pulley and Belt on your 2007 – 2011 Jeep Wrangler”