Double Line Winching Techniques Demonstrated and Explained in Simple Terms
Using a Double line winch pull method with a snatch block can when properly accomplished give you 2x the pulling power of your winch.
Do It Yourself – Simple Step by Step Instructions on How to Remove and Replace The Oil Filter / Cooler Assembly on your 2012 and Newer Jeep Wrangler using common tools
Parts Recommended:Upper and Lower Intake Gaskets – MS97204Oil Filter/Cooler Housing – 68105583AE Tools Required: 8mm Socket 10mm Socket Ratchet 3” and 6” extensions Body Clip Tool T20 Torx T30 Torx E8 (External) Torx Small flat tip screwdriver Standard Pliers Wide Tape to cover intake ports Brake Cleaner or similar, to clean intake and oil filter/cooler …
Do It Yourself how to Install a 3.5 inch Suspension Lift Kit on a 2007 – 2018 Jeep Wrangler
Tools Needed: 10mm Wrench, 14 mm Wrench, 16mm Wrench, 18mm Wrench, 18mm Socket, 19mm Wrench, 19mm Deep Well Socket, 7/8″ Wrench, 13/16″ Socket, 21mm Wrench, 21mm Socket, 7/16″ Wrench, 9/16″ Wrench, 9/16″ Socket, 33mm Socket, Jack, (4) 6 ton Jack Stands, (2) 3 ton Jack stands, 13/32″ Drill bit, Drill, Pitman Arm Puller, PB Blaster, …
How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others
Jeep Wrangler JK JKU Pinion Bearing Removal and Replacement Refer to JK_JKU Hub Bearing Replacement video for more detailed instructions on removal and Installation of the Hub Bearing and Axle Shaft. https://youtu.be/9uOOXPxBr8M Tool Suggested: 1/2″ Drive Ratchet 1/2″ Drive Breaker Bar 1/2″ Drive Torque Wrench capable of 120 ft lbs 3/8″ Drive Ratchet 1/4″ Drive …
Read more “How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others”
Complete Factory Parts List for the Jeep Wrangler JK / JKU
How to Do It fabricate your own Starter Heat Shielding
I had to fabricate a heat shield because mine on my JKU was missing. I had to replace the starter because of heat damage, it is about ¾” from a catalytic converter. This is the heat barrier which has adhesive on the back and what I used to protect the metal I used for the …
Read more “How to Do It fabricate your own Starter Heat Shielding”
Iron Rock Off-road Control Arm Adjustment Jeep Wrangler JKU
This is specifically for Iron Rock Offroad Adjustable Control Arms – After installation and testing has occured, it is time to adjust for better performance. This process is similar for most adjustable control arms, clamping nuts and bolts may differ but the procedure is the same.
How to Remove and Replace on a Driver Side Exhaust Manifold on a Jeep Wrangler JK/JKU (3.8L Motor)
Left Side (Driver Side) Exhaust Manifold Replacement on a Jeep Wrangler JK or JKU (3.8L Motor) Applies to 2007-2011 Jeep Wrangler (JK/JKU) Exhaust Manifold Replacement Mopar PN: 4666024AD Exhaust Manifold Gasket Replacement FelPro PN: MS 96908 Tools Recommended: 10″ Vise Grips 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive 14″ extension …
Do It Yourself – How to Remove and Replace the Water Pump on a Jeep Wrangler JK / JKU 3.8L Motor
This procedure applies to 2007-2011 Jeep Wrangler (JK/JKU) with a 3.8l V-6 Motor Parts Used:Water Pump Replacement Mopar PN: 4666044BB.0Water Pump Gasket Replacement Mopar PN: 4666068AA Tools Recommended: Wire Brush Gasket Scraper Small Pry Bar 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive Breaker Bar 3/8″ Drive 10mm Socket 3/8″ Drive …
Do It Yourself – How to Remove and Replace a Hub Bearing on a 2007 – 2020 Jeep Wrangler Unlimited
This is the removal and replacement of a 2009 JKU Passenger side Hub Bearing. This video starts after you have already raised the Jeep and supported it properly with jack stands and removed the tire. This procedure should work for many other years and models of Jeep. 1987-2018. There will be slight variations in the …