Death Wobble Prevention – A Simple and Effective Suspension Inspection

by Kurt EadesLearn, VideoPosted on No Comments

Front ends shakes, wobbles, shimmies and the dreaded Death Wobble. These have been going on since steering was invented and has worsened with the incorporation of coil spring suspensions. Prevention is the key to any well maintained Jeep. Preventive Maintenance and Routine Inspections and not of just the Stereo Equipment. We used a Floor Jack, …

Read more “Death Wobble Prevention – A Simple and Effective Suspension Inspection”

Do It Yourself – Simple Step by Step Instructions on How to Remove and Replace The Oil Filter / Cooler Assembly on your 2012 and Newer Jeep Wrangler using common tools

by Kurt EadesLearn, VideoPosted on No Comments

Parts Recommended:Upper and Lower Intake Gaskets – MS97204Oil Filter/Cooler Housing – 68105583AE Tools Required: 8mm Socket 10mm Socket Ratchet 3” and 6” extensions Body Clip Tool T20 Torx T30 Torx E8 (External) Torx Small flat tip screwdriver Standard Pliers Wide Tape to cover intake ports Brake Cleaner or similar, to clean intake and oil filter/cooler …

Read more “Do It Yourself – Simple Step by Step Instructions on How to Remove and Replace The Oil Filter / Cooler Assembly on your 2012 and Newer Jeep Wrangler using common tools”

Do It Yourself how to Install a 3.5 inch Suspension Lift Kit on a 2007 – 2018 Jeep Wrangler

by Kurt EadesLearn, VideoPosted on No Comments

Tools Needed: 10mm Wrench, 14 mm Wrench, 16mm Wrench, 18mm Wrench, 18mm Socket, 19mm Wrench, 19mm Deep Well Socket, 7/8″ Wrench, 13/16″ Socket, 21mm Wrench, 21mm Socket, 7/16″ Wrench, 9/16″ Wrench, 9/16″ Socket, 33mm Socket, Jack, (4) 6 ton Jack Stands, (2) 3 ton Jack stands, 13/32″ Drill bit, Drill, Pitman Arm Puller, PB Blaster, …

Read more “Do It Yourself how to Install a 3.5 inch Suspension Lift Kit on a 2007 – 2018 Jeep Wrangler”

How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others

by Kurt EadesLearn, VideoPosted on No Comments

Jeep Wrangler JK JKU Pinion Bearing Removal and Replacement Refer to JK_JKU Hub Bearing Replacement video for more detailed instructions on removal and Installation of the Hub Bearing and Axle Shaft. https://youtu.be/9uOOXPxBr8M Tool Suggested: 1/2″ Drive Ratchet 1/2″ Drive Breaker Bar 1/2″ Drive Torque Wrench capable of 120 ft lbs 3/8″ Drive Ratchet 1/4″ Drive …

Read more “How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others”

exhaust manifold

How to Remove and Replace on a Driver Side Exhaust Manifold on a Jeep Wrangler JK/JKU (3.8L Motor)

by Kurt EadesLearn, VideoPosted on No Comments

Left Side (Driver Side) Exhaust Manifold Replacement on a Jeep Wrangler JK or JKU (3.8L Motor) Applies to 2007-2011 Jeep Wrangler (JK/JKU) Exhaust Manifold Replacement Mopar PN: 4666024AD Exhaust Manifold Gasket Replacement FelPro PN: MS 96908 Tools Recommended: 10″ Vise Grips 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive 14″ extension …

Read more “How to Remove and Replace on a Driver Side Exhaust Manifold on a Jeep Wrangler JK/JKU (3.8L Motor)”

Water Pump

Do It Yourself – How to Remove and Replace the Water Pump on a Jeep Wrangler JK / JKU 3.8L Motor

by Kurt EadesLearn, VideoPosted on No Comments

This procedure applies to 2007-2011 Jeep Wrangler (JK/JKU) with a 3.8l V-6 Motor Parts Used:Water Pump Replacement Mopar PN: 4666044BB.0Water Pump Gasket Replacement Mopar PN: 4666068AA Tools Recommended: Wire Brush Gasket Scraper Small Pry Bar 3/8″ Drive – Inch lb Torque Wrench 3/8″ Drive Ratchet 3/8″ Drive Breaker Bar 3/8″ Drive 10mm Socket 3/8″ Drive …

Read more “Do It Yourself – How to Remove and Replace the Water Pump on a Jeep Wrangler JK / JKU 3.8L Motor”