The contents of the video are almost ALL of the current maintenance and installation videos within the It’s a Jeep World YouTube Channel.
Tag: Jeep
Learn
Double Line Winching Techniques Demonstrated and Explained in Simple Terms
Using a Double line winch pull method with a snatch block can when properly accomplished give you 2x the pulling power of your winch.
Posted on by
Learn
How To – JK/JKU Fuel Tank Relocation / TJ Fuel Tank Swap
Compliments Riley Harshman the Owner of the Jeep and who provided the information, check out his WAYALIFE Thread “Birth of Phoenix” The main question you have to ask yourself when researching this swap, “Do you go with a Fuel cell, aftermarket tank or do the TJ fuel tank swap?” A Fuel Cell takes up needed […]
Posted on by
Learn
Jeep Wrangler JKU Hardtop Removal Tips
Explanation of what you need to do to actually be able to remove your freedom top panels and hardtop. Bolts to remove, levers to move, latches to unlatch, connectors to disconnect, etc.. This video has a hoist system which is used. Manual removal is explained as well.Shout outs to https://www.facebook.com/IG4wlusa/, https://www.sevenslotsociety.com/, http://onthetrailpodcast.com/ w/Kevin and Scott. […]
Posted on by
Learn
Keep It Simple, a Guide for Wheel Backspace and Offset
So easy a Jeeper Figured it out. What is Wheel Offset and Backspace? Wheel offset and backspacing two different ways of looking at same thing. Determines the location of the wheel and tire assembly when bolted onto the wheel hub. They determine how far in or out the wheel and tire sit. Why is it […]
Posted on by
Learn
Death Wobble Prevention – A Simple and Effective Suspension Inspection
Front ends shakes, wobbles, shimmies and the dreaded Death Wobble. These have been going on since steering was invented and has worsened with the incorporation of coil spring suspensions. Prevention is the key to any well maintained Jeep. Preventive Maintenance and Routine Inspections and not of just the Stereo Equipment. We used a Floor Jack, […]
Posted on by
Learn
Do It Yourself – Simple Step by Step Instructions on How to Remove and Replace The Oil Filter / Cooler Assembly on your 2012 and Newer Jeep Wrangler using common tools
Parts Recommended:Upper and Lower Intake Gaskets – MS97204Oil Filter/Cooler Housing – 68105583AE Tools Required: 8mm Socket 10mm Socket Ratchet 3” and 6” extensions Body Clip Tool T20 Torx T30 Torx E8 (External) Torx Small flat tip screwdriver Standard Pliers Wide Tape to cover intake ports Brake Cleaner or similar, to clean intake and oil filter/cooler […]
Posted on by
Learn
Do It Yourself how to Install a 3.5 inch Suspension Lift Kit on a 2007 – 2018 Jeep Wrangler
Tools Needed: 10mm Wrench, 14 mm Wrench, 16mm Wrench, 18mm Wrench, 18mm Socket, 19mm Wrench, 19mm Deep Well Socket, 7/8″ Wrench, 13/16″ Socket, 21mm Wrench, 21mm Socket, 7/16″ Wrench, 9/16″ Wrench, 9/16″ Socket, 33mm Socket, Jack, (4) 6 ton Jack Stands, (2) 3 ton Jack stands, 13/32″ Drill bit, Drill, Pitman Arm Puller, PB Blaster, […]
Posted on by
Learn
How to – Remove and Replace the Pinion Bearing on a Jeep Wrangler JK JKU and others
Jeep Wrangler JK JKU Pinion Bearing Removal and Replacement Refer to JK_JKU Hub Bearing Replacement video for more detailed instructions on removal and Installation of the Hub Bearing and Axle Shaft. https://youtu.be/9uOOXPxBr8M Tool Suggested: 1/2″ Drive Ratchet 1/2″ Drive Breaker Bar 1/2″ Drive Torque Wrench capable of 120 ft lbs 3/8″ Drive Ratchet 1/4″ Drive […]